Amplia

Measure Floor Plans: Room Dimensions and Area from an Image

Open a floor plan as an image — a scan, a screenshot from a listing, a photo of a printed sheet. Click one dimension that is written on it, then read every wall length and every room's area. The plan does not have to be printed to scale.

  • One written dimension sets the scale for the whole plan
  • Rooms of any shape: L-shaped, angled walls, a bay
  • Square meters or square feet, wall by wall lengths, corner angles
  • Free, in your browser. Used as a guest, the plan never leaves your device
Living roomKitchenBathHallBedroom9.605.40S1 · 28.08 m²S2 · 11.88 m²B1B29.60 mL1 · 3.10 m4.00 mm/px
  • Known size: the written width
  • Living room
  • Bedroom
  • One wall

A plan on the screen, not a room in front of you

Use this page when you have the plan

  • A scan or a photo of a printed plan
  • A screenshot of a plan from a listing, a brochure or a PDF viewer
  • An image exported from drawing software
  • An old drawing with no file behind it

Use something else when

  • You have the room, not the plan. A photo of a room is not a plan: the floor runs away from the camera, so one scale cannot fit it. Measure the room with a tape or a laser distance meter, or use your phone's AR measuring app for a rough figure.
  • You have the CAD or BIM file. The software that made the drawing reads exact lengths and areas from the model. An image is the fallback for when the file is gone.
  • You need a figure for a contract or an appraisal. That is a measured survey of the building, to a named standard. A plan image gives an estimate; Which area is this? below explains why.

"1:100" was true for one sheet of paper

A scale ratio compares the paper with the building: at 1:100, one centimeter on the sheet is one meter of wall. It holds only on the sheet size the drawing was made for. Everything that happens to the plan afterwards changes it.

Original sheet

Says 1:100, and is 1:100.

Printed smaller

Still says 1:100. It is now 1:200.

Screenshot

Still says 1:100. It is whatever the zoom was.

The orange bar is the plan's drawn 2 m scale bar. It changes size with the plan; the "1:100" note does not.

Printed to fit.

An A1 sheet printed on A3 is at 50 % — the 1:100 plan is now 1:200. On A4 it is at 35 %, about 1:283. A US 24 × 36 in sheet at ¼″ = 1′-0″ printed on tabloid paper is at 46 %, about 1:105; on letter paper, about 1:157.

Scanned or photographed.

The image has pixels, not centimeters. A scanner's resolution setting says how many pixels it made per inch of that paper — which is already the wrong size if the print was.

Screenshot.

A screenshot has whatever zoom the viewer was at. There is no scale left in it at all.

Copied on old machines.

Photocopiers and fax machines stretch a page slightly more in one direction than the other.

Ignore the ratio. Trust one written dimension.

This is why drawings carry the note "do not scale": a length taken off the paper with a ruler is not trusted; the written dimension is. Measuring on an image follows the same rule the other way round.

Ignore the ratio. Take one written dimension as the truth and let it set the scale. Then it does not matter what happened to the sheet.

A drawn scale bar survives all of this, because it is resized together with the plan. A ratio in the title block does not.

What common scales mean on the original sheet

What common drawing scales mean on the original sheet
ScaleOn paperIn the building
1:501 cm0.5 m
1:1001 cm1 m
1:2001 cm2 m
¼″ = 1′-0″ (1:48)1 in4 ft
3/16″ = 1′-0″ (1:64)1 in5 ft 4 in
⅛″ = 1′-0″ (1:96)1 in8 ft

Pick the longest dimension the plan gives you

Calibration is two clicks and a number: you mark the two ends of a length you know and type its value. Every later measurement inherits the error of those two clicks, so the choice of reference matters more than anything you do afterwards. In order of preference:

  1. An overall dimension.

    The outer string of dimensions — the full width or depth of the building — is the longest length on the sheet. Click the two tick marks (or arrowheads) where the dimension line ends, not the walls: the ticks are what the number refers to.

  2. A room dimension.

    "4.20 × 3.60" printed inside a room is good when the plan has no dimension lines. Ask what it measures: on most listing plans it is the clear distance between the inner wall faces, so click inner face to inner face.

  3. The drawn scale bar.

    Reliable, but usually short — a 2 m or a 10 ft bar is a fraction of the plan's width. Use its full length, end mark to end mark.

  4. A door.

    The last resort, for a plan with no numbers at all. A door leaf is drawn as a line with a quarter-circle swing; the line's length is the door's width. Common widths are 30 in and 32 in (762 and 813 mm) for US interior doors and 762 mm for UK internal doors — but you are guessing which one, and the guess goes straight into every result.

02 m9.603.60 × 3.301234

How much the reference's length matters

Take a plan 12 m wide that fills 2,400 pixels of the image, and suppose your two clicks are off by 2 pixels in total.

Error carried into every length and area by a 2-pixel miss on the calibration points, by reference length
ReferenceLength on the imageError in every lengthError in every area
Overall width, 12.00 m2,400 px0.08 %0.17 %
Room dimension, 4.20 m840 px0.24 %0.48 %
Scale bar, 2 m400 px0.50 %1.00 %
Door leaf, 0.80 m160 px1.25 %2.52 %

Areas take twice the error of lengths, because the scale is applied in both directions. And the door carries a second, larger risk: type 30 in for a door that is really 32 in and every length reads 6 % short and every area 12 % short, however carefully you click.

Tip:

Zoom in before you click. On a phone, press and hold to place a point under a magnified strip instead of under your fingertip.

Three checks that take a minute

Measure a second dimension at a right angle to the first.

If you calibrated on the plan's width, draw a Line along a written depth. It should read what is printed. Within about 1 % the plan is fine. If the widths agree and the depths are all off by the same few percent, the copy was stretched in one direction; calibrate on a dimension that runs the way your most important measurements run, and treat areas as approximate.

Measure one dimension at the far end of the sheet.

A plan photographed with a phone held at a slant is wider at one edge than the other. If a dimension near the top reads right and one near the bottom reads wrong, the photo is the problem. Scan the sheet, or lay it flat and shoot from directly above with the sheet filling the frame, then straighten it with Crop & rotate — before calibrating, because applying a crop clears the calibration.

Look for "not to scale".

Listing and brochure plans are often redrawn for looks, with the note "for illustration only" or "NTS". Their room labels may be right while the drawing is not. If two written dimensions disagree with each other when measured, believe the labels and use the drawing only for shapes.

Calibrate across, check down. The check line reads what is printed.
Photographed at a slant. The same 3.60 is drawn at two lengths.

Measure a floor plan in five steps

  1. Open the plan as an image.

    A JPEG or PNG, a phone photo (HEIC is converted as it opens) or a TIFF from a scanner. As a guest it stays in your browser.

  2. Calibrate on a written dimension.

    Choose the Calibration tool, click the two ends of the longest dimension on the plan, and type its value and unit.

  3. Check a second dimension.

    The Line tool: two clicks along another written dimension, at a right angle to the first. It should read what is printed.

  4. Outline each room.

    The Polygon tool: click each corner along the inner wall faces, then ✓ Finish. The label shows the room's area.

  5. Read the details.

    Click a room's label: its perimeter, its area and the length of every side are listed. Add them up room by room for the total.

The measuring tools ask for the calibration first. Changing the calibration value later re-scales everything already drawn, so a mistyped dimension costs nothing to fix.

Two rooms from one dimension

A small apartment plan, saved as a screenshot. The only thing taken on trust is the overall width written under the plan: 9.60 m.

  1. 1Calibrate on that dimension, tick mark to tick mark: 9.60, meters.
  2. 2Check against the depth written beside the living room, 5.40 m. The Line reads 5.38 m — 0.4 % off, which is a click's worth. Carry on.
  3. 3Living room, L-shaped: six corners with the Polygon tool.
  4. 4Bedroom, a rectangle: four corners.
The two rooms of the example plan: their sides, perimeters and areas
RoomSidesPerimeterArea
Living room S16.00 · 3.60 · 2.40 · 1.80 · 3.60 · 5.40 m22.80 m28.08 m²
Bedroom S23.60 · 3.30 · 3.60 · 3.30 m13.80 m11.88 m²
Both39.96 m²

The same plan calibrated in feet (9.60 m is 31.50 ft) reads 302.25 ft² and 127.88 ft², 430.13 ft² together. Values on a real image land within the click error of these; the table shows the plan's true figures.

S1 — Polygon

Details
Perimeter
P 22.80 m
Area
A 28.08 m²
Corners
5 at 90°, 1 at 270°

Segments6

6.00 m3.60 m2.40 m1.80 m3.60 m5.40 m

Two things the details add that the label does not: the list of side lengths, which is the wall-by-wall schedule a fitter asks for, and the angle at every corner, which shows at once whether a wall you assumed square is drawn square.

The total is a sum you make yourself; each polygon reports its own room.

Three honest answers for the same house

The area you get depends on where you click, and so does every published figure. A house 10 × 8 m outside, with 30 cm external walls and 20 m of 10 cm partitions, has three different areas.

Outer face

80.0 m² 861 ft²

Outside of the external walls.

Inner face of the perimeter

69.56 m² 749 ft² · −13 %

Inside of the external walls, partitions included.

Inner faces of every room

67.56 m² 727 ft² · −16 %

The rooms, added up.

None of these is wrong. They are different definitions, and standards pick different ones:

In the United States

The ANSI Z765 standard for houses measures finished area to the outside face of the exterior walls, counts only space with a ceiling of at least 7 ft, and reports whole square feet. It does not cover apartments or the sizes of individual rooms.

In the United Kingdom and under IPMS

Under the international IPMS standards, the usual residential figure is taken to the inside face of the perimeter walls and includes the internal walls — gross internal area.

A flooring or painting job

Needs the third: the rooms themselves.

So when your figure comes out 10–15 % below the one in the listing, check the definition before you doubt the measurement. And decide where to click before you start: a room traced along the middle of its 20 cm walls instead of their inner faces reads 4.40 × 3.80 m instead of 4.20 × 3.60 m — 10.6 % more floor than exists.

Ceiling heights, sloped attics and which rooms count are not on a plan image at all. A figure for a sale, a lease or a valuation comes from a measured survey.

Flooring, skirting, and feet with inches

Flooring.

Order the room's area plus a cutting allowance: about 10 % for boards or tiles laid straight, about 15 % for a diagonal or herringbone layout, and more for a room with many corners. The living room above, with packs that cover 2.22 m²:

28.08 × 1.10 = 30.89 m² → 13.9 → 14 packs

28.08 × 1.15 = 32.29 m² → 15 packs, laid herringbone

Skirting and trim.

Start from the perimeter, take out the door openings, add 10 % for cuts. The living room, in 2.4 m lengths:

22.80 − 2 × 0.80 = 21.20 m

21.20 × 1.10 = 23.32 m → 10 lengths

Feet and inches.

Dimensions on US plans are written in feet and inches; Amplia reads lengths in decimal feet. Converting takes one division — inches ÷ 12:

Inches as decimal feet
Inches1234567891011
Feet0.0830.1670.250.3330.4170.50.5830.6670.750.8330.917

To calibrate on a dimension written 13′-4″, type 13.333 feet, or switch the unit to inches and type 160. A wall that reads 12.5 ft is 12′-6″.

Other units. Areas follow the unit you calibrated in: meters give m², feet give ft². A shape's Converter tab shows the same value in the neighboring units of that family.

Three shortcuts, and what each one needs

02 m2 mCalibrated from the scale barEdit
A new project that opened already calibrated. Look at the baseline before you measure.

A scale bar that calibrates the plan.

Create a project from a plan with a drawn scale bar and it can open already calibrated: the baseline sits on the bar's ends, set to the length read from its label. It needs a free account, a new project, and a bar labeled in metric units — a bar in feet is not read. The label is applied as read, not verified, so look at the baseline before you measure; a dialog lets you move its ends between the centers and the outer edges of the bar's end marks and correct the value.

The magic wand for a room.

With the Polygon tool active, the wand outlines the region you click; more clicks add or remove parts, and Finish turns it into an ordinary polygon with draggable corners. On a plan it works best where rooms are filled or clearly closed off. Treat the outline as a suggestion: check that it follows the wall faces you chose, and fix the corners that do not. It is not available in every browser.

A grid in real units.

Once the plan is calibrated, a grid can be drawn over it with a step you set — 1 m, 60 cm, 2 ft — and shifted so a line sits on a wall. It measures nothing; it is for judging whether a 2 m sofa fits or counting how many tile rows cross a room.

A plan the next person can read

Apartment plan — flooringLiving room and bedroom, measured from the listing planLiving roomKitchenBathHallBedroom9.605.40S1 · 28.08 m²S2 · 11.88 m²B1B29.60 mCalibrationB1–B2, two points9.60 mPolygons#PerimeterAreaCommentS122.80 m28.08 m²oak, laid lengthwiseS213.80 m11.88 m²—Made with AmpliaPage 1

Notes on the plan.

Add a comment to a room's outline ("oak, laid lengthwise") or drop a numbered note pin anywhere ("radiator moves here").

A PDF report.

The annotated plan on top, then the calibration and a table of every measurement with its comments. Choose the paper size, orientation, title and description.

The annotated image.

The plan with every outline and label drawn on it, at the image's original resolution.

A link.

Share the project read-only: the other person can pan, zoom and open each measurement, and cannot change anything.

Reports, images and links come from a project saved in a free account with a verified email address; exports have a monthly allowance and carry Amplia branding on the free plan. Saving a project stores the plan image in your account, and you can delete it permanently at any time. Comments · PDF report · Image export · Share link · Projects

What a plan image cannot give you

Holes are yours to subtract.

An outline cannot cross itself, so a column, a shaft or a stairwell inside a room is a second polygon whose area you take away.

Curved walls are approximated.

A polygon follows a curve with short straight sides; more corners, less error. The Curve area tool PRO draws a smooth outline instead.

A PDF has to become an image.

Take a screenshot of the page at high zoom, or export the page as PNG or JPEG. Starting a project directly from a PDF page is a PRO option.

A slanted photo stays slanted.

Rescan it or reshoot from above. Perspective calibration PRO measures a flat surface photographed at an angle from a rectangle of known size.

Small rooms on a small image are coarse.

If a wall is 40 pixels long, one pixel is 2.5 % of it. Use the largest image you can get.

The plan may not match the building.

Walls get moved and drawings are not updated. Before ordering anything expensive, measure one room for real.

Frequently asked questions

Can I measure a floor plan that is not to scale?

Yes, as long as it is drawn in proportion and shows one dimension you can trust. You mark that dimension once and it sets the scale; the ratio printed on the sheet is not used. A plan redrawn "for illustration only" may be out of proportion, and then no tool can recover real sizes from it.

How do I calculate the area of a room from a floor plan?

Calibrate on a written dimension, then click the room's corners with the Polygon tool and finish the outline. The label shows the area; the details add the perimeter and the length of each side. For a whole floor, outline each room and add the areas.

How do I get square footage from a floor plan image?

Enter the calibration in feet and every area reads in square feet. If the plan is dimensioned in meters, calibrate in meters and multiply m² by 10.764.

The plan only has a scale like 1:100. Can I use that?

Not directly: the ratio applies to the original sheet, and an image has no sheet size. If the plan has a drawn scale bar, calibrate on the bar. If it has neither a bar nor a dimension, a door width is the last resort, and the result is a rough estimate.

Can it read the scale bar for me?

A new project created from a plan with a drawn metric scale bar can open already calibrated from it. That needs a free account, and the value is applied as read from the label, so check the baseline first. In the guest workspace you calibrate by clicking the bar's two ends yourself.

Why is my area smaller than the one in the listing?

Most often because the listing counts wall thickness and you measured the rooms. A figure taken to the outside of the external walls can be 10–15 % above the sum of the rooms. Compare like with like before assuming an error.

Does it work in feet and inches?

You can calibrate in feet or inches and read lengths in decimal feet and areas in square feet. A dimension written 12′-6″ is entered as 12.5 ft or 150 in.

Can I open a PDF plan?

As an image, yes: take a screenshot of the page or export it as PNG or JPEG and open that. Creating a project directly from a PDF page is a PRO option.

How accurate is it?

On a clean scan calibrated on a long dimension, lengths are typically within a fraction of a percent of what the plan says and areas within about one percent. The plan's own accuracy is a separate question — a drawing is not a survey.

Can it find all the rooms automatically?

No. The magic wand can outline one region you click, as a suggestion to check and adjust; rooms are outlined one at a time and totals are added by you.

Is my plan uploaded?

Not while you work as a guest: the image is opened and measured in your browser and never leaves your device. If you save it as a project in a free account, the image is stored so you can reopen and share it, and you can delete it permanently at any time.

Is it free?

Measuring is free and needs no account: the Line, Polyline, Polygon, Circle, Angle and Comment tools. A free account adds saved projects, sharing, and PDF and image exports. A few tools and options are marked PRO.

Open your floor plan and measure it

No install and no account needed to start. Click one dimension you trust, then outline the rooms. Or try it first on the built-in sample image — it is a floor plan.

Open the free tool