Amplia

Measure Walls, Windows and Openings from a Photo

Take one straight-on photo of the wall with something of known size in it — a door, a run of bricks, a tape mark. Click that size once, then read the wall's width, height and area, and every window and door in it.

  • One known size in the photo sets the scale for the whole wall
  • Walls of any shape: gables, stair walls, a wall with a door cut out of it
  • Meters or feet and inches; areas in m² or ft²
  • Free, in your browser. Used as a guest, the photo never leaves your device
2,032 mm8.19 m²1.44 m²7.27 mm/px
  • Known size: the door
  • Wall area, door left out
  • Window

What this does — and what it does not

Amplia measures on a picture you already have. It is not a ruler that works through a live camera, and it cannot measure a wall with nothing of known size in the photo.

It fits when

  • You have a photo of the wall, or can take one, and you know one real size in it
  • You are quoting from photos a client sent, or checking a number after leaving the site
  • You need an area — to paint, tile, paper or board — and the wall is not a plain rectangle
  • You want the measurements drawn on the photo, to hand to a crew or a client

Use something else when

  • You are standing in the room and need one length now. A tape or a laser distance meter is faster and more exact
  • You want to point the phone at the wall and read a size off the screen. That is an AR measuring app, and it needs no reference; this tool does
  • You are ordering a made-to-measure window, door or worktop. Measure the opening itself — see openings
  • Nothing in the photo has a size you know or can find out

How to photograph a wall so it can be measured

A photo is a flat picture, and one scale fits it only when the wall is flat to the camera. Thirty seconds spent on the shot is worth more than any care taken afterwards.

  1. Stand square to the wall.

    Opposite its middle, not in the doorway at one end. The floor line and the ceiling line should run level across the frame and stay the same distance apart from left to right.

  2. Hold the phone upright, at half the wall's height.

    Tilting it up to fit the ceiling makes the top of the wall narrower than the bottom. Raise the phone or step back instead.

  3. Step back as far as the room allows.

    Distance shrinks every error on this page. If the wall does not fit, shoot it in two overlapping halves and measure each with its own reference.

  4. Use the main lens.

    The ultra-wide (0.5×) lens bends straight lines near the edges of the frame, and bent lines cannot be measured.

  5. Keep the reference in the wall's plane.

    A closed door, the bricks or tiles of the wall itself, a strip of tape stuck to it. An open door, a chair or a person in front of the wall is at another distance and gives a wrong scale.

Top viewWall to measureOpposite the middle, not from the doorwaySide viewHalf heightUpright, at half the wall's height

If the photo came out slightly rotated, straighten it with Crop & rotate before you calibrate — applying a crop clears the calibration, so crop first.

What to calibrate on in a wall photo

Calibration is two clicks on a length you know, plus its value. The best reference is long, lies in the wall itself, and sits near what you are measuring. The one you measured yourself beats any standard size.

Things in a wall photo that can serve as the known size, from most to least reliable
ReferenceTypical sizeHow goodWatch for
Your own tape measurement — the wall's width, or two tape marks on itwhatever you measuredbestwrite it down before you leave
A level or straightedge held flat against the wallits stated lengthvery goodflat on the wall, not leaning
Door leaf height, door closedUS: 80 in (2,032 mm) · UK: 1,981 mm (6 ft 6 in)goodclick the leaf, not the trim; other heights exist, so check one door on site
Brick courses, countedUS modular: 3 courses = 8 in · UK: 4 courses = 300 mmgoodover 10 or more coursesjoints vary; older bricks are not modular
Bricks along a courseUS modular: 8 in per brick with joint · UK: 225 mmgoodover 6 or more brickscount joints with the bricks
Concrete blocksUS: 16 × 8 in with joint · UK: 450 × 225 mm with jointgood—
Wall tiles, counted with their jointsthe tile's nominal size, e.g. 300 × 600 mmfair to gooda "300 mm" tile is often a few millimeters smaller; measure one tile plus joint
Stud spacing or drywall sheet width, on an unfinished wallUS: studs 16 in on center, sheets 4 ft wide · metric sheets 1,200 mmfair24 in spacing also exists
Socket or switch plateUS: 4.5 × 2.75 in (also sold as 4.88 × 3.13 and 5.25 × 3.5) · UK: 86 × 86 mm single, 146 × 86 mm doublelast resortsmall, and you cannot tell the plate sizes apart in a photo

Why length matters

Every measurement inherits the error of the two calibration clicks. In a photo where 5 m of wall spans 4,000 pixels, missing the reference's ends by 3 pixels in total costs:

Error carried into every measurement by a 3-pixel miss on the calibration points, by reference length
ReferenceLength in the photoError in every measurement
Door leaf, 2,032 mm1,626 px0.2 %
Ten brick courses, 750 mm600 px0.5 %
One 300 mm tile240 px1.3 %
One brick, 215 mm172 px1.7 %
Socket plate, 114 mm91 px3.3 %

A US plate that turns out to be the mid-size one adds another 8 % on top. Count ten courses rather than one brick; use the door rather than the socket.

1 · Door2 · Ten courses3 · One tile4 · Socket

On a phone, press and hold instead of tapping to place a point: a magnified strip opens at the top of the screen and a slow finger moves the point finely. On a computer, zoom in with the wheel before you click.

How far off can a wall measurement be?

The arithmetic is exact. The error comes from the photo: how square it is, and whether everything you measure lies in the wall's plane.

Slightly off square is not slightly wrong.

When the camera is turned a few degrees, one end of the wall is nearer than the other, and near things look bigger. The table is for a wall 4 m wide shot from 4 m away, calibrated on a door in the middle:

Measurement error on a 4 m wall photographed from 4 m, by how far the camera is turned off square
Camera off square byWhole wall widthA 1 m window at the near endThe same window at the far end
5°0.2 % short6.5 % too big6.6 % too small
10°0.8 % short12.7 % too big13.2 % too small
20°3.2 % short24 % too big26 % too small
Square onFrom 20° to the sidelargersmaller

Three things follow:

The whole wall forgives; its parts do not.

Across the full width the near and far halves nearly cancel. A window at one end gets no such help.

Calibrate next to what you measure.

A reference beside the window shares its distance from the camera, and most of the error goes with it. For a window schedule, calibrate once per window — on that window's own brickwork or sill, or on a tape mark beside it.

Step back.

From 6 m, the 5° row drops to about 4 %.

Check before you trust.

Measure the ceiling height at both ends of the wall. In a square-on photo the two agree. If one end reads 2.40 m and the other 2.20 m, the camera was turned, and everything between is off by a share of that difference. The same test works for an upward tilt: the wall's width along the floor and along the ceiling should agree.

Things that are not in the wall's plane

A window set back in its reveal.

Glass 10 cm behind the wall face, shot from 4 m, reads about 2.4 % small; 20 cm back, about 5 %. Measure the opening at the wall face, where the calibration holds.

Anything in front of the wall.

A radiator 10 cm proud reads about 2.6 % large. A cabinet whose front is 50 cm into the room reads 14 % large — calibrate on the cabinet front to measure the cabinet.

The side wall, the floor, the ceiling.

They run away from the camera. One photo measures one wall.

Bays, curves and chimney breasts.

Each face is its own plane; shoot and calibrate each one separately.

CabinetWindow glass, in its revealWall face: the calibration plane10 cm behind the facereads about 2.4 % small50 cm in frontreads about 14 % largeCamera, 4 m from the wall

Measure a wall in five steps

  1. Open the photo.

    Load it from your phone or computer; an iPhone's HEIC photo is converted as it opens. As a guest it stays in your browser.

  2. Calibrate.

    Choose the Calibration tool, click the two ends of your reference — the bottom and top of the door leaf — and type its size and unit.

  3. Measure widths and heights.

    The Line tool: two clicks give a length. Wall width, ceiling height, sill height, the width of each opening. Each line gets a label — L1, L2 — and its value.

  4. Outline the wall.

    The Polygon tool: click each corner, then ✓ Finish. The label shows the area; the details show the perimeter too. A wall does not have to be a rectangle.

  5. Outline each opening and subtract.

    One polygon per window or door. Net wall area is the wall's area minus theirs — a subtraction you do yourself; see the example below.

1 · Calibrate on the door2 · Lines3 · Polygons2,032 mmL1 4.20 mL2 2.40 mS1 8.19 m²S2 1.44 m²

The Angle tool and comments work on an uncalibrated photo; every other measuring tool asks for the calibration first. Changing the calibration value later re-scales everything already drawn. Calibration · Line · Polygon · Image formats

Net wall area, with the door and window taken out

Amplia gives you each area; it does not subtract one shape from another. There are two honest ways to get the net figure.

Way 1 — outline, then subtract.

Net area of a wall with one door and one window, from three polygons
ShapeWhat it isArea
S1the wall, 4.20 m × 2.40 m10.08 m²
S2the door, 0.90 m × 2.10 m1.89 m²
S3the window, 1.20 m × 1.20 m1.44 m²
Net wall: S1 − S2 − S36.75 m²

Way 2 — walk around the door.

An opening that reaches the floor or the edge of the wall can be left out of the wall's own outline: click along the floor to the door, up its side, across its head, down the other side, and on along the floor. That one polygon reads 8.19 m² straight away. A window in the middle of the wall is a hole, and a polygon cannot have a hole — outline it separately and subtract: 8.19 − 1.44 = 6.75 m².

S2A 1.44 m²S1A 8.19 m²S1Polygon · 8 pointsDetailsConverterPPerimeter17.40 mAArea8.19 m²

Getting the numbers out

Click a label to open the shape's details: the area and perimeter are listed there, and in the Converter tab a click on a value copies it. The PDF report lists every polygon's area in one section.

The magic wand can outline a window for you

With the Polygon tool active, press the wand and click the window: it proposes an outline you can correct and then finish as an ordinary polygon. Treat it as a suggestion and check the corners. It appears only in browsers that support it.

Not a rectangle?

A gable end, a wall under a staircase, a wall with a sloped ceiling: the polygon follows whatever corners you click. This is where a photo beats multiplying width by height.

From net area to paint, tile, wallpaper and board

Amplia stops at the measurement. The step from area to an order is short arithmetic, and it differs by trade. Each line below uses the 6.75 m² wall from the example.

Paint

Liters = net area × coats ÷ coverage

A typical wall paint covers about 350–400 sq ft per US gallon per coat — roughly 9–10 m² per liter — but the figure on the can is the one to use, and rough or unprimed surfaces take more.

Example: 6.75 m² × 2 coats ÷ 10 m² per liter = 1.35 L. In US units: 72.7 sq ft × 2 ÷ 375 = 0.39 gallon — two quarts.

Many painters leave small openings in: the extra covers cutting in and touch-ups.

Wallpaper

Drops = wall width ÷ roll width, rounded up

Drops per roll = roll length ÷ cut length, rounded down

Wallpaper is counted in drops, not in area. The cut length is the wall height plus trim, rounded up to a whole number of pattern repeats.

Example: a 4.20 m wall and a standard 0.53 m × 10.05 m roll: 4.20 ÷ 0.53 = 7.9, so 8 drops. Plain paper, 2.40 m + 0.10 m trim = 2.50 m per drop: 4 drops per roll, 2 rolls. With a 64 cm repeat each drop is cut at 2.56 m: 3 drops per roll, 3 rolls. The pattern repeat changed the order by a roll; the area did not.

Tile

Tiles = net area × (1 + waste) ÷ area of one tile

Allow about 10 % for a straight layout and 15 % for a diagonal one.

Example: 6.75 m² × 1.10 = 7.43 m². With 300 × 600 mm tiles (0.18 m² each): 41.25, so 42 tiles — then round up to full boxes.

Drywall and sheet materials

Sheets = gross wall area ÷ sheet area, rounded up

Boards are hung across ordinary openings and cut out, so use the wall's full area, not the net one.

Example: 10.08 m² ÷ 2.88 m² (a 1,200 × 2,400 mm sheet) = 3.5, so 4 sheets. A 4 × 8 ft sheet is 32 sq ft.

See the layout before you cut.

Once the photo is calibrated, the grid can be drawn in real units: set its step to one tile plus joint — 60 cm across, 30 cm down — and shift its offset until a line sits on the wall's corner. You see where the cut tiles fall and can count full rows by eye. Set the step to the roll width and it shows the wallpaper drops instead. The grid is a visual aid: it measures nothing, and it only matches a wall shot square-on and level.

These are estimating numbers for a quote or a shopping list. Before an expensive order, check one dimension on site with a tape.

Grid 60 × 30 cmCut tile,30 cmCut row, 10 cmGrid offset on the wall's corner

Windows, doors and openings: good for a quote, not for an order

A photo tells you how big an opening is to within the errors above. A made-to-measure unit needs millimeters, and it needs them from the opening itself.

What a photo does well

  • A first quote from a client's picture. Size class, number of units, whether it is a standard size.
  • A window schedule for a facade or a room. Every opening labeled and listed, with its position on the wall.
  • Heights you cannot reach. A sill height, a head height, a transom, measured against the door or the brickwork beside it.
  • A record. What the opening looked like, and which dimension was taken where.

What it cannot do

  • Replace the three-point survey. Installers measure an opening's width at the top, middle and bottom and its height at left, center and right, and order to the smallest of each, because openings are rarely square. One photo gives one reading.
  • See depth. The reveal, the sill projection and the wall thickness run toward the camera.
  • Tell you which size you clicked. The visible glass, the frame, the trim and the structural opening behind it are four different sizes. Decide which one you are measuring and say so in a comment on the shape.
W topW middleW bottomH leftH centerH rightStructural openingTrimFrameGlass

Tip: For a single window, calibrate on something beside that window — its own brick courses, or a tape mark on the wall next to it — and not on a door at the other end of the wall.

Hand it over: notes on the photo, a report for the crew

A number on a scrap of paper loses its wall. Keep the measurement on the picture it came from.

AmpliaMeasurement reportLiving room, east wallQuote: repaint, two coats. Tile splashback to 1.20 m.S1 *S2CalibrationB1–B2, door leaf2,032 mmLinesL1Wall width4.20 mL2Window width1.20 mPolygonsLabelShapePAS1 *Wall, around the door17.40 m8.19 m²S2Window4.80 m1.44 m²CommentsS1— tile to 1.20 m, paint abovePage 1 of 1

Notes where they belong

Add a comment to any shape — "tile to 1.20 m, paint above" — or drop a note pin anywhere on the photo: "socket to be moved", "damp patch, treat first". A commented shape shows an asterisk next to its label.

A PDF report

The annotated photo at the top, then the calibration, every length and every area by type, and your comments and notes as their own sections. Choose the paper size, orientation, title and description.

The annotated photo as an image

The picture at its original resolution with everything drawn on it — for a message to the client or a job folder.

A read-only link

Share the project by link, or invite one person by email. They see the photo, the scale and every measurement, can pan and zoom, and cannot change anything.

Measuring needs no account. Saving a project, sharing and exporting need a free account with a verified email, and exports have a monthly allowance. Free exports carry the Amplia header. Projects

The photo was taken at an angle — now what?

Reshoot it if you can. Square-on, from further back, following the five rules above. It takes a minute and costs nothing.

If you cannot — a client's photo, a narrow corridor, a wall you will not see again:

Measure near the reference.

Calibrate beside each thing you measure, and re-calibrate when you move to the next one. Each reading is then about as good as the photo allows locally.

Trust heights at the reference's position, not across the wall.

In a wall shot from the side, vertical sizes right next to the door are close; a height at the far end is not.

Do not take an area.

A polygon over a wall that narrows to one side has no single scale.

Perspective calibrationPRO

Made for this case. Instead of one known length you describe a rectangle you know — its width, height and four corners — and measurements are mapped through the wall's plane. Its limits, stated plainly: it lives inside a saved project, it measures only inside the rectangle you marked, so the rectangle should be the wall itself or enclose what you measure, and the Circle tool is unavailable while it is active.

Frequently asked questions

Can you measure a wall from a picture?

Yes, if the picture shows one thing whose real size you know and the wall was photographed straight on. Mark that size once — a door's height, a run of bricks — and the wall's width, height and area follow from it.

Can I point my phone at the wall and measure it live?

No. Amplia works on a photo, not through the live camera, and it needs a known size in the picture. For a quick reading while you stand in the room, a tape, a laser distance meter or your phone's AR measuring app is the right tool.

What can I use as the known size?

The best is a length you measured yourself: the wall's width, or two tape marks on it. After that, a closed door's height, a counted run of brick courses or tiles, and — as a last resort — a socket plate. Longer is better, and it must lie flat in the wall.

How accurate is it?

On a square-on photo with a long reference, typically within a few percent. The error grows with the camera's angle and with distance from the reference: turned just 5°, a window at the end of a 4 m wall can read 6 % off while the wall's full width stays within 1 %. Check by measuring the ceiling height at both ends.

How do I subtract windows and doors from the wall area?

Outline the wall with the Polygon tool, outline each opening with its own polygon, and subtract their areas from the wall's. A door that reaches the floor can be left out by clicking the wall's outline around it. The subtraction itself is yours to do.

Does it work out how much paint, tile or wallpaper I need?

No. It gives you the lengths and areas; the quantity is a short calculation from there, shown above for each material. Wallpaper is counted in drops from the wall's width, not from its area.

My photo was taken at an angle. Can I still use it?

For rough sizes near your reference, yes; for an area or a size at the far end, no. Reshoot square-on if you can. Perspective calibration, a PRO feature, measures a wall photographed at an angle from a rectangle of known size.

Can I order a window from these measurements?

No. Use the photo for a quote, a schedule or a record. A made-to-measure unit is ordered from the opening itself, measured at three points across and three points up.

Can I work in feet and inches?

Yes. Enter the calibration in feet or inches and lengths read in imperial units, areas in square feet. Metric works the same way, and you can change the unit later without redrawing.

Is my photo uploaded?

Not while you work as a guest: the photo is opened and measured in your browser and never leaves your device. If you save it as a project in a free account, the image is stored so you can reopen and share it, and you can delete it permanently at any time.

Does it work on a phone?

Yes. It runs in the browser on phones and tablets and can be installed like an app. Take the photo with the camera, open it, and press and hold to place points precisely.

Is it free?

Measuring is free and needs no account: the Line, Polyline, Polygon, Circle, Angle and Comment tools. A free account adds saved projects, sharing, and PDF and image exports. A few tools and options are marked PRO.

Open your wall photo and measure it

No install and no account needed to start. Click a size you know, then read the rest of the wall. Or try it first on the built-in sample image.

Open the free tool