Drone, straight down
The file says how high and which way.
Open a picture of the land taken from above — your own drone photo, a screenshot of a satellite view, a scanned survey map. Give it a scale, click the corners of the plot, and read its area and the length of every side. A DJI or Parrot photo shot straight down brings an estimated scale with it.
The file says how high and which way.
A length you know on the ground.
The scale bar in the corner.
A written dimension.
Orange marks the thing that gives each image its scale.
| Image | Where the scale comes from | One pixel on the ground |
|---|---|---|
| Drone photo, straight down, original DJI or Parrot file | the flight data in the file — an estimate, applied when the photo opens | 1–4 cm at 30–120 m |
| Any other drone photo | a length you know on the ground | 1–4 cm |
| Satellite or map screenshot | the scale bar in the corner, or a distance you know | about 10 cm for a 200 m view on a full-HD screen |
| Scanned survey map, plat or site plan | a written dimension or the drawn scale bar | depends on the scan |
Two things follow from the last column. A drone photo is five to ten times sharper than a screenshot, so the edge you click is the real edge and not a blur of four pixels. And a screenshot is only as sharp as your screen: zooming the map in before you capture it does more for the result than anything you do afterwards.
For a scanned plan or plat, the rules are the ones for any drawing: ignore the printed ratio and calibrate on a written dimension. They are on the Measure floor plans page.
Imagery in a map service is often a few years old. If a fence was moved or a field was split last spring, only your own photo shows it.
A drone writes more into a photo than the picture. A DJI or Parrot (ANAFI) file records how high the drone was and which way the camera pointed, next to the lens's focal length. From a photo taken straight down, that is enough to work out how much ground one pixel covers — the figure surveyors call ground sample distance:
ground per pixel = height above the ground × sensor width ÷ (focal length × image width in pixels)
For a small camera drone — a sensor 9.6 mm wide behind a 6.66 mm lens, 4,000 pixels across — at 60 m that is 60 × 9.6 ÷ (6.66 × 4,000) = 0.0216 m. A little over 2 cm per pixel, and a frame about 86 × 65 m.
Amplia reads this when the photo opens and applies it. There is nothing to click:
It is free, it needs no account, and it works on the first upload of the file. The value is applied, not verified — and for a drone it is an estimate, for one reason above all.
A DJI drone measures its height from the spot where it took off. The formula needs the height above the ground in the picture. On a flat site those are the same number. They are not the same when:
The altitude itself comes from a barometer and can be a few meters off. The Calibration dialog says so in one line: "Assumes flat ground shot straight down from 55 m above takeoff. May be off by several percent."
A tilted DJI or Parrot photo is not left unexplained: the Calibration dialog names the tilt in degrees and tells you why it applied nothing. In every one of these cases you calibrate by hand on a known length, exactly as on any other image. An Autel photo is recognized and its flight details are listed, but it gets no automatic scale.
The error in the scale is the error in the height, as a fraction: if the land is 3 m closer to the camera than the file says, at 60 m every length is 5 % off. Areas take about twice that, because the scale applies in both directions.
| Height above takeoff | Height off by 2 m | Height off by 5 m | ||
|---|---|---|---|---|
| Lengths | Areas | Lengths | Areas | |
| 20 m | 10 % | 21 % | 25 % | 56 % |
| 40 m | 5 % | 10 % | 12.5 % | 27 % |
| 80 m | 2.5 % | 5 % | 6 % | 13 % |
| 120 m | 1.7 % | 3.4 % | 4 % | 9 % |
Read it across, not down: higher is better. The height error is a fixed few meters, so its share shrinks as you climb. The pixels get coarser, but at 120 m one pixel is still about 4 cm — far smaller than the error it replaces. A low pass over a small yard is the worst case for the estimate and the best case for calibrating by hand.
Tilt adds its own share. At the 10° limit the scale in the middle of the frame is already off by 1.5–3 %, and it changes from one edge to the other.
Gimbal pitch −90°. A tilt you cannot see in the picture is enough to stretch one side of the plot.
Launch from the field, not from the road embankment above it. Then the height in the file is the height above what you measure.
Keep the land in the middle half of the frame. The lens is least faithful at the edges, and the middle is where straight down is really straight down.
Long shadows hide the foot of a fence or a hedge, and that foot is the line you will click.
Two posts you have taped, a painted parking bay, the side of a container. It costs nothing in the air and turns an estimate into a measurement.
Copy it from the card. An edited or forwarded copy may open without its scale.
For a camera with a 24 mm-equivalent lens and a 4,000 × 3,000 pixel photo:
| Height | Frame on the ground | Frame area | One pixel |
|---|---|---|---|
| 30 m (100 ft) | 43 × 32 m | 0.14 ha (0.35 acre) | 1.1 cm |
| 60 m (200 ft) | 86 × 65 m | 0.56 ha (1.4 acres) | 2.2 cm |
| 90 m (300 ft) | 130 × 97 m | 1.26 ha (3.1 acres) | 3.2 cm |
| 120 m (400 ft) | 173 × 130 m | 2.25 ha (5.5 acres) | 4.3 cm |
120 m in the EU and 400 ft in the US are the usual legal ceilings, so about two hectares is the most a single photo holds — and half of that once you keep the plot away from the edges. A larger field needs a satellite image or a stitched map.
Tip
After the photo opens, the Info dialog's Scale tab shows the width and height of the whole frame in real units. If it says 86 × 65 m and you know the paddock is about 50 m long, you have a first check before drawing anything.
Whatever gave the image its scale — flight data, a scale bar, your own two clicks — measure one thing whose size you know before you trust an area. Draw a Line along it and compare.
| Reference | Size | How far to trust it |
|---|---|---|
| A length you taped yourself | as measured | best — make it as long as the site allows |
| Tennis court, doubles lines | 23.77 × 10.97 m (78 × 36 ft) | exact by rule |
| Soccer penalty area | 40.32 × 16.5 m (44 × 18 yd) | exact by rule; the pitch itself varies |
| Basketball court | 28 × 15 m (FIBA), 94 × 50 ft (US) | exact by rule |
| Competition swimming pool | 25 m or 50 m long | exact for a competition pool |
| Shipping container | 6.06 m or 12.19 m long, 2.44 m wide | exact |
| Parking bay | about 2.4 × 4.8 m (UK), 9 × 18 ft (US) | rough — it varies by site |
| A car | 4–5 m | a guess; last resort |
Choose the longest one. Two clicks that are each a pixel off cost 2 % on a 100-pixel reference and 0.2 % on a 1,000-pixel one.
Correct the scale in one of two ways:
On an image with no scale of its own, the known length is the calibration: choose the Calibration tool, click its two ends, type the value and the unit.
The original JPEG from the drone, a screenshot, or a scan. As a guest it stays in your browser.
A straight-down DJI or Parrot photo already has an estimated one. On anything else, choose the Calibration tool, click the two ends of a length you know, and type its value and unit.
The Line tool: two clicks along something whose size you know. It should read what you expect.
The Polygon tool: click each corner of the boundary, then ✓ Finish. The label shows the area.
Click the label: the area, the perimeter and the length of every side are listed. Add a comment to say which line you took as the boundary.
The measuring tools ask for a scale first. Changing the calibration value later re-scales everything already drawn, so a corrected scale costs nothing.
A straight-down photo from a small DJI drone, taken from 55 m above the driveway it launched from. The frame covers about 79 × 59 m, and the photo opens at ≈ 2 cm/px.
| Value | Before the check | After |
|---|---|---|
| West side | 35.1 m | 34.0 m |
| Perimeter | 170.7 m | 165.4 m |
| Area S1 | 1,906 m² | 1,788 m²0.18 ha · 0.44 acre · 19,246 ft² |
The sides after the correction: 48.0 · 22.8 · 30.0 · 30.6 · 34.0 m.
S1 — Polygon
DetailsSegments5
48.0 m22.8 m30.0 m30.6 m34.0 m
A 3 % error in the scale became a 6.6 % error in the area — 118 m², the footprint of a small house — and one taped fence found it.
Without the check, 1,906 m² is still a usable estimate for ordering grass seed. It is not a figure for a contract.
A screenshot has no scale of its own, but the map it came from drew one in the corner. Four things decide how good the result is:
Top-down, not the tilted 3D view: a tilted view shrinks everything toward the horizon.
then capture. The screenshot is as sharp as your screen, no sharper.
It was drawn for exactly this zoom, so it is resized with everything else.
A 20 m bar is about 190 pixels on a full-HD screenshot of a 200 m view; two pixels of click error there are 1 % in length and 2 % in area. A known 180 m between two road corners cuts that to a tenth. The map's own measure tool will give you such a distance.
Small print. Satellite and aerial imagery in a map service belongs to the service and its suppliers. Measuring on a screenshot for your own use is one thing; publishing the annotated picture is governed by their terms. Your own drone photo has no such strings.
Then outline the land as on any image. Measure at ground level: on aerial imagery tall buildings lean away from the center of the frame, so a roof outline is not where the walls stand, and tree crowns hide the fence under them.
With a free account, a new project made from an image with a drawn scale bar may open already calibrated from it. The label is read in metric units only and applied as read, so look at the baseline before you measure.
Calibrate in meters and a yard reads in m², a large field in hectares. Calibrate in feet and they read in ft² and acres. A drone's estimated scale arrives in metric; to read acres, change the subsystem to Imperial in the Calibration dialog. A shape's Converter tab shows the same value in the neighboring units of its family.
| Unit | Equals |
|---|---|
| 1 hectare | 10,000 m² · 2.471 acres |
| 1 acre | 43,560 ft² · 4,047 m² · 0.4047 ha |
| 1 square mile | 640 acres · 259 ha |
| A full-size soccer pitch, 105 × 68 m | 0.71 ha · 1.76 acres |
US and British land records are often written in chains and rods. The Surveying family reads them directly: calibrate on a boundary given as "12.50 chains" and lengths come out in chains, areas in square chains and acres.
1 chain66 ft4 rods100 links
Ten square chains make exactly one acre.
A picture from above shows the land as a map does: projected flat. That is also what a deed records. The surface you actually walk, fence or seed is larger:
| Slope | Ground vs map area |
|---|---|
| 5° (9 % grade) | + 0.4 % |
| 10° (18 %) | + 1.5 % |
| 15° (27 %) | + 3.5 % |
| 20° (36 %) | + 6.4 % |
| 30° (58 %) | + 15.5 % |
Up to about 10° the difference is smaller than anything else on this page. On a steep hillside, order materials for the larger figure.
With the Polygon tool active, the wand selects the region you click — a mown lawn, a plowed field, a pond. More clicks add a part it missed or cut away one it took by mistake, and Finish turns the result into an ordinary polygon with corners you can drag. It works where the land looks different from what surrounds it. Treat the outline as a suggestion: it follows what the picture shows, which is a hedge's shadow as readily as the hedge. It is not available in every browser.
Once the image has a scale, a grid can be drawn over it with a step you set — 10 m, 25 ft — and shifted so a line sits on a fence. It measures nothing; it is for laying out beds and rows, or for counting sample squares across a field.
The Info dialog shows how much ground the whole image covers, and, for a drone photo, the height, the camera angle and the other details the file recorded.
The inside of the hedge, its middle, or the fence behind it? Tracing half a meter outside the true line all the way around a 40 × 45 m plot adds 4.8 % to its area. Decide first, and write it in a comment.
The result is an estimate for planning, quoting and ordering. Boundaries, easements and setbacks are not in the picture.
The scale holds for the ground level it was set on. Roofs, terraces and the far side of a slope are closer to or farther from the camera, and read wrong.
Reshoot straight down. Perspective calibration PRO measures a flat surface photographed at an angle from a rectangle of known size.
An outline cannot cross itself, so a house or a pond inside the plot is a second polygon whose area you take away.
A polygon follows a riverbank with short straight sides; more corners, less error. The Curve area tool PRO draws a smooth outline instead.
Tree crowns, long shadows and snow cover the line you need. Another season or another hour shows it.
From above you see the footprint. The Measure angle page has the pitch table that turns one into the other.
Take a top-down screenshot with the scale bar in it, open it, and calibrate on the bar or on a longer distance you know. Then click the corners of the land with the Polygon tool and finish the outline: the label shows the area, the details add the perimeter and every side.
Yes, if it was taken straight down over flat ground. A DJI or Parrot original opens with an estimated scale from its flight data; any other photo is calibrated on one known length. A site too large for one frame needs a stitched map or a satellite image.
DJI and Parrot (ANAFI) photos taken straight down, opened as the original file. The DJI Mini 2 SE, Mini 3 and Mini 4K record no camera angles, so their photos are calibrated by hand. Autel photos are recognized and their flight details are shown, without an automatic scale.
The usual reasons: the camera was tilted more than 10° from straight down, the file was edited or re-saved, the drone was under 5 m up, the photo used digital zoom, or the flight data was stripped when the file was sent through a messenger. Calibrate on a known length instead.
It depends on how well the height in the file matches the height above your land. On flat ground that you took off from, expect a few percent; lower flights and uneven ground do worse. Measure one known length and correct the scale if it disagrees — after that, accuracy is that of your reference.
Yes. A metric scale reads in square meters and hectares, an imperial one in square feet and acres. A drone's estimated scale is metric; change the subsystem in the Calibration dialog to read acres. One hectare is 2.471 acres.
You can measure on it like on any image: calibrate on its scale bar or a known distance. If all you need is one area, the map's own measure tool is quicker. The imagery belongs to the map service, so check its terms before publishing an annotated screenshot.
No. It measures what you outline. Legal boundaries are not visible in any image, and only a licensed surveyor can establish them.
A picture from above gives the flat, map area — the one deeds use. The ground surface is larger: 1.5 % at a 10° slope, 6.4 % at 20°. A single drone photo of a slope is also less reliable, because the high end is closer to the camera.
Fly higher if you legally can, use a satellite image, or stitch the photos into one map with photogrammetry software and open the exported image. Calibrate it on a known distance.
Not while you work as a guest: the image is opened and measured in your browser and never leaves your device. If you save it as a project in a free account, the image is stored so you can reopen and share it, and you can delete it permanently at any time.
Measuring is free and needs no account: the Line, Polyline, Polygon, Circle, Angle and Comment tools, and the estimated scale for drone photos. A free account adds saved projects, sharing, and PDF and image exports. A few tools and options are marked PRO.
No install and no account needed to start. A straight-down drone photo brings its own estimated scale; anything else takes one known distance. Or try the tools first on the built-in sample image.
Open the free tool